Plumbing 101: What You Must Have for Installing a Bathtub
Plumbing 101: What You Must Have for Installing a Bathtub
Blog Article
What are your concepts about Tools You Need to Install a New Bathtub ?
Setting up a bath tub isn't precisely brain surgery, but it does need solid plumbing, woodworking, as well as sometimes, tiling abilities. Replacing an old bath tub with a new one is also a moderately challenging project. If the old bathtub is readily available, the task can relocate speedily; if you have to open a wall to eliminate the old tub and also position the brand-new bath tub, the job is a lot harder. In either situation, the project is within a home handyman's skills, although you will certainly require an assistant to leave the old bathtub and set in the brand-new one. Make certain you have actually certified on your own for the job as well as fit trying it. As opposed to employing a service provider to take over a halfway-completed job, it is better to take into consideration utilizing one prior to you start. Opportunities are you may require a professional plumber to make tube connections.
This post will certainly assist you mount a new tub in your shower room if you have currently purchased a new tub and don't require to change the plan of your previous water pipelines.
Your devices as well as material list must make up the following:
Removing Old Taps
If you require to replace old faucets with brand-new ones as a part of your installation, then the first thing you must do is disconnect the water system. After doing so, activate the taps to drain pipes any water staying in the system. The procedure of removing the existing taps can be rather troublesome as a result of the limited accessibility that is commonly the case.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the taps. Have a cloth all set for the remaining water that will come from the pipelines. Once the supply pipes have actually been gotten rid of, utilize the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will need to quit the single taps from transforming throughout this procedure. When the taps have actually been removed, the holes in the bath/basin will have to be cleansed of any type of old sealing compound.
Prior to moving on to fit the new faucets, contrast the pipe links on the old faucets to the brand-new taps. If the old taps are longer than the new taps, after that a shank adapter is needed for the brand-new taps to fit.
Fitting New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly need a plastic connector to avoid damage to the thread. One end of the adapter fits on the plastic tail of the faucet and the various other end provides a link to the current supply pipes.
If you need to fit a monobloc, then you will require lowering couplers, which connects the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next, place the tap in the placing opening in the bath/basin guaranteeing that the washers are in area between the tap and the sink. Secure the faucet in position with the producer given backnut. Once the faucet is firmly in place, the supply pipelines can be linked to the tails of the faucets. The faucets can either be attached by using corrugated copper piping or with typical tap adapters. The former type ought to be attached to the faucet ends first, tightening just by hand. The supply pipes can later on be connected to the other end. Tighten up both ends with a spanner after both ends have been connected.
Installing the Bath tub
Making use of both wood boards under its feet, place the bath tub in the required placement. The wood boards are handy in equally spreading the weight of the bathtub over the area of the boards as opposed to focusing all the weight onto four tiny points.
The next goal is to make sure that the bathtub is leveled all round. This can be accomplished by examining the spirit level as well as adjusting the feet on the bath tub till the spirit level reads level.
To install faucets, fit the bottom of the furthest adaptable faucet connector to the ideal supply pipe by making a compression sign up with; after that do the same for the other tap.
Turn on the water system as well as inspect all joints as well as brand-new pipework for leakages and also tighten them if required. Fill the tub as well as additionally examine the overflow outlet and the normal electrical outlet for leakages.
Ultimately, take care of the bathroom paneling as described in the manufacturer's user's manual. Tiling and sealing around the tub must wait up until the tub has been used at the very least once as this will certainly resolve it into its last placement.
Planning for the Installment
First of all, the sustaining structure supplied with the bathroom should be fitted (if required) according to the manufacturer's instructions. Next off, fit the taps or mixer to the bathtub. When suitable the faucet block, it is very important to ensure that if the tap features a plastic washing machine, it is fitted between the bath as well as the faucets. On a plastic bath, it is likewise practical to fit a sustaining plate under the faucets unit to stop strain on the bathtub.
Fit the versatile faucet ports to the bottom of the two taps utilizing 2 nuts and also olives (occasionally supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet through the hole in the bath. Make use of the nut provided by the supplier to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make certain you use all of the supplied washing machines.
Attach the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom ought to now be ready to be suited its final placement.
Tiling Around the Bath tub
In the area where the bathroom satisfies the ceramic tile, it is essential to secure the joins with a silicone rubber caulking. This is necessary as the installation can relocate sufficient to fracture an inflexible seal, triggering the water to penetrate the wall in between the bath and the tiling, causing issues with dampness as well as feasible leakages to the ceiling listed below.
You can pick from a selection of coloured sealers to blend in your fixtures and fittings. They are sold in tubes and also cartridges, and also are capable of securing voids up to a size of 3mm (1/8 inch). If you have a larger space to load, you can load it with twists of soaked newspaper or soft rope. Keep in mind to always load the tub with water prior to sealing, to allow for the motion experienced when the bathtub is in usage. The sealant can split rather very early if you do not consider this activity prior to sealing.
Additionally, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise conveniently readily available on the market. It is recommended to fit the ceramic tiles making use of water-resistant or water-proof adhesive and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I have been very enthusiastic about How to Install a Bathtub Yourself and I am praying you liked our blog entry. If you please take a moment to share this blog if you enjoyed it. We enjoy reading our article about How to Install a Bathtub.
Suggested Site Report this page